GB-1GBEXZ2610DLEXZ2610DLGBOWNER’S MANUALCONVERTIBLEBRUSHCUTTER848JPY93A0 (806)
GB-10EXZ2610DL1. When you finish cutting in one loca-tion and wish to continue work in an-other spot, turn off the engine, lift upthe unit and carry i
GB-11GBEXZ2610DLInsert the cableto the end ofadjusterFull on stopperIdling adjust screwM3 screwAdjusterMOUNTING ENGINE1. Push the shaft tube toward th
GB-12EXZ2610DL(1)(1)(2)(3)6. Set up (BC-EX only)INSTALLING CUTTING ATTACHMENT GUARD• Put the cutting attachment guard on the gearbox, at-tach it with
GB-13GBEXZ2610DL(1)(2)(3)(4)(5)6. Set up (PS-EX only)6. Set up (LRT-EX only)ATTACHING THE TRIMMING MECHANISM(1) Main pipe(2) Trimming mechanism(3) Scr
GB-14EXZ2610DL6. Set up (HE-EX only)4. Adjust the chain tension by turning the tensioner screwuntil the tie straps just touch the bottom side of theba
GB-15GBEXZ2610DL7. Fuel and chain oil FUEL WARNING• Gasoline is very flammable. Avoid smoking orbringing any flame or sparks near fuel. Make sureto
GB-16EXZ2610DLSTARTING ENGINE(HE-EX only)The ZENOAH stick edger is designed for edging lawn ingardens, parks, roadsides and so on.Before starting the
GB-17GBEXZ2610DL123(1)(1) Stop switch8. Operation5. Set the stop switch to the “-” position. Set the throttletrigger to the start position (1 → 2 → 3)
GB-18EXZ2610DL8. OperationADJUSTING THROTTLE CABLE• The normal play is 1 or 2 mm when measured at thecarburetor side end. Readjust with the cable adju
GB-19GBEXZ2610DLCUTTING WORK (LINE HEAD USAGE) WARNING1. Always wear eye protection such as safetygoggles. Never lean over the rotating cutting head.R
GB-2EXZ2610DLEXPLANATION OF SYMBOLS AND SAFETY WARNINGSAPPROVAL NUMBER OF CE EXHAUST EMISSION REGULATIONDIRECTIVE 97/68/EC AMENDED 2002/88/ECe13*97/68
GB-20EXZ2610DLCHOOSE THE BLADEChoose a suitable recommended cutting attachmentaccording to the object to be cut.• When replacing blade always be sure
GB-21GBEXZ2610DLSTARTING THE ENGINEPlease refer to 5. For safe operation (P. 7 ~ 9), 8. Ope-ration (P. 15 ~ 17). WARNINGThe product is equipped with a
GB-22EXZ2610DL8. Operation (Optional blade usage BC-EX only) WARNINGMake sure to use shoulder strap and cutting attach-ment guard. If not, it is very
GB-23GBEXZ2610DL8. Operation (LRT-EX only) WARNINGThis product is equipped with extremely sharp blades,and when used improperly these blades can be ex
GB-24EXZ2610DL WARNING• Always wear eye protection such as safetygoggles. Never lean over the rotating cutting head.Rocks or other debris could be thr
GB-25GBEXZ2610DL WARNING• Make sure that the engine has stopped and is coolbefore performing any service to the machine. Con-tact with moving cutting
GB-26EXZ2610DLSPARK PLUG• Starting failure and misfiring are often caused by afouled spark plug. Clean the spark plug and checkthat the plug gap is in
GB-27GBEXZ2610DL9. Maintenance IMPORTANT• If waste gets stuck and causes blockage around theintake air cooling vent or between the cylinder fins, itma
GB-28EXZ2610DL9. Maintenance (BC-EX only)BLADES• When refilling the tank or resting, it is often a goodidea to use the time to oil the cutting blades.
GB-29GBEXZ2610DLOILING PORTDismount the guide bar and check the oiling port forclogging.(1)(1) Oiling portGUIDE BARRemove sawdust in the bar groove an
GB-3GBEXZ2610DLSAFETY FIRSTInstructions contained in warnings within this manual markedwith a symbol concern critical points which must be takeninto
GB-30EXZ2610DLPlace your file on the cutter and push straightforward.Keep the file position as illustrated.After every cutter has been set, check the
GB-31GBEXZ2610DLTRANSMISSION• The reduction gears are lubricated by multipurpose,lithium-based grease in the transmission. At every 20hours of use, su
GB-32EXZ2610DLShould any failure occur on the product under normaloperating conditions within the applicable warranty pe-riod, the failed part will be
GB-4EXZ2610DLBC-EXEXZ2610DL-PUOPS-EXLRT-EXHE-EX15161718192021222324252623456891011121314171. Parts location11. Loop handle12. Suspension point13. Stop
GB-5GBEXZ2610DL2. SpecificationEngineType ... Air-cooled 2-stroke gasolineMod
GB-6EXZ2610DL4. Symbols on the machineFor safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,
GB-7GBEXZ2610DL1. Read this manual carefully untilyou completely understand andfollow all safety and operatinginstructions.2. Keep this manual handy s
GB-8EXZ2610DLBEFORE STARTINGTHE ENGINE1. The area within a perimeter of15 m of the person using theproduct should be considered ahazardous area into w
GB-9GBEXZ2610DL7. Never operate the pruner at anangle greater than 60° in order toreduce the risk of being struck byfalling objects during operation.
Commentaires sur ces manuels